Network Working Group
Request for Comments: 1764
Category: Standards Track
S. Senum
DigiBoard
March 1995

The PPP XNS IDP Control Protocol (XNSCP)

Status of this Memo

This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited.

Abstract

The Point-to-Point Protocol (PPP) [1] provides a standard method for transporting multi-protocol datagrams over point-to-point links. PPP defines an extensible Link Control Protocol, and proposes a family of Network Control Protocols for establishing and configuring different network-layer protocols.

This document defines the Network Control Protocol for establishing and configuring the Xerox Network Systems (XNS) Internet Datagram Protocol (IDP) over PPP.

Table of Contents

   1.     Introduction ..........................................    2
      1.1       Specification of Requirements ...................    2
      1.2       Terminology .....................................    3
   2.     A PPP Network Control Protocol for XNS IDP ............    3
      2.1       Sending XNS IDP Datagrams .......................    4
   SECURITY CONSIDERATIONS ......................................    5
   REFERENCES ...................................................    5
      ACKNOWLEDGEMENTS ..........................................    5
   CHAIR'S ADDRESS ..............................................    5
   AUTHOR'S ADDRESS .............................................    5

1. Introduction

PPP has three main components:

  1. A method for encapsulating multi-protocol datagrams.
  1. A Link Control Protocol (LCP) for establishing, configuring, and testing the data-link connection.
  1. A family of Network Control Protocols for establishing and configuring different network-layer protocols.

In order to establish communications over a point-to-point link, each end of the PPP link must first send LCP packets to configure and test the data link. After the link has been established and optional facilities have been negotiated as needed by the LCP, PPP must send XNSCP packets to choose and configure the XNS IDP network-layer protocol. Once XNSCP has reached the Opened state, XNS IDP datagrams can be sent over the link.

The link will remain configured for communications until explicit LCP or XNSCP packets close the link down, or until some external event occurs (an inactivity timer expires or network administrator intervention).

1.1. Specification of Requirements

In this document, several words are used to signify the requirements of the specification. These words are often capitalized.

   MUST      This word, or the adjective "required", means that the
             definition is an absolute requirement of the specification.
   
   MUST NOT  This phrase means that the definition is an absolute
             prohibition of the specification.
   
   SHOULD    This word, or the adjective "recommended", means that there
             may exist valid reasons in particular circumstances to
             ignore this item, but the full implications must be
             understood and carefully weighed before choosing a
             different course.
   
   MAY       This word, or the adjective "optional", means that this
             item is one of an allowed set of alternatives.  An
             implementation which does not include this option MUST be
             prepared to interoperate with another implementation which
             does include the option.

1.2. Terminology

This document frequently uses the following terms:

   datagram  The unit of transmission in the network layer (such as IP).
             A datagram may be encapsulated in one or more packets
             passed to the data link layer.
   
   frame     The unit of transmission at the data link layer.  A frame
             may include a header and/or a trailer, along with some
             number of units of data.
   
   packet    The basic unit of encapsulation, which is passed across the
             interface between the network layer and the data link
             layer.  A packet is usually mapped to a frame; the
             exceptions are when data link layer fragmentation is being
             performed, or when multiple packets are incorporated into a
             single frame.
   
   peer      The other end of the point-to-point link.

silently discard

This means the implementation discards the packet without further processing. The implementation SHOULD provide the capability of logging the error, including the contents of the silently discarded packet, and SHOULD record the event in a statistics counter.

2. A PPP Network Control Protocol for XNS IDP

The XNS IDP Control Protocol (XNSCP) is responsible for configuring, enabling, and disabling the XNS IDP protocol modules on both ends of the point-to-point link. XNSCP uses the same packet exchange mechanism as the Link Control Protocol (LCP). XNSCP packets may not be exchanged until PPP has reached the Network-Layer Protocol phase. XNSCP packets received before this phase is reached should be silently discarded.

The XNS IDP Control Protocol is exactly the same as the Link Control Protocol [1] with the following exceptions:

   Frame Modifications

The packet may utilize any modifications to the basic frame format which have been negotiated during the Link Establishment phase.

Data Link Layer Protocol Field

Exactly one XNSCP packet is encapsulated in the Information field of a PPP Data Link Layer frame, where the PPP Protocol field indicates type hex 8025 (XNS IDP Control Protocol).

   Code field
   
      Only Codes 1 through 7 (Configure-Request, Configure-Ack,
      Configure-Nak, Configure-Reject, Terminate-Request, Terminate-Ack
      and Code-Reject) are used.  Other Codes should be treated as
      unrecognized and should result in Code-Rejects.
   
   Timeouts

XNSCP packets may not be exchanged until PPP has reached the Network-Layer Protocol phase. An implementation should be prepared to wait for Authentication and Link Quality Determination to finish before timing out waiting for a Configure-Ack or other response. It is suggested that an implementation give up only after user intervention or a configurable amount of time.

   Configuration Option Types

XNSCP has no Configuration Options.

2.1. Sending XNS IDP Datagrams

Before any XNS IDP packets may be communicated, PPP must reach the Network-Layer Protocol phase, and the XNS IDP Control Protocol must reach the Opened state.

Exactly one XNS IDP packet is encapsulated in the Information field of a PPP Data Link Layer frame where the Protocol field indicates type hex 0025 (XNS IDP datagram).

The maximum length of a XNS IDP datagram transmitted over a PPP link is the same as the maximum length of the Information field of a PPP data link layer frame. Since there is no standard method for fragmenting and reassembling XNS IDP datagrams, PPP links supporting XNS IDP MUST allow at least 576 octets in the information field of a data link layer frame.

The format of the Information field itself is the same as that defined in [2].

Security Considerations

Security issues are not discussed in this memo.

References

   [1] Simpson, W., "The Point-to-Point Protocol (PPP)", STD 51, RFC
       1661, Daydreamer, July 1994.

[2] Xerox, "Internet Transport Protocols", January 1991, Order No.

XNSS 029101.

Acknowledgements

Some of the text in this document is taken from previous documents produced by the Point-to-Point Protocol Working Group of the Internet Engineering Task Force (IETF).

In particular, Bill Simpson provided the boiler-plate used to create this document.

Chair's Address

The working group can be contacted via the current chair:

Fred Baker
Cisco Systems
519 Lado Drive
Santa Barbara, California 93111

   Phone: (805) 681-0115
   EMail: fred@cisco.com

Author's Address

Questions about this memo can also be directed to:

Steven J. Senum
DigiBoard
6400 Flying Cloud Drive
Eden Prairie, Minnesota 55344

   Phone: (612) 943-9020
   EMail: sjs@digibd.com