Request For Comments: 787 A. Lyman Chapin
July 1981
Subject: Connectionless Data Transmission Survey/Tutorial
From: A. Lyman Chapin
The attached paper on connectionless data transmission is being distributed to the members of a number of US organizations that are involved or interested in the development of international data communication standards. Following a review period ending Septem- ber 1, 1981, a revised version of the paper - incorporating com- ments and suggestions received from reviewers - will be considered by the American National Standards Institute (ANSI) committee responsible for Open Systems Interconnection (OSI) Reference Model issues (ANSC X3T5). If approved, it will then be presented to the relevant International Organization for Standardization (ISO) groups as the foundation of a US position recommending the incor- poration of connectionless data transmission by the Reference Model and related OSI service and protocol standards. Your comments on the paper, as well as an indication of the extent to which the concepts and services of connectionless data transmis- sion are important to you and/or your organization, will help to ensure that the final version reflects a true US position. They should be directed to the author at the following address:
A. Lyman Chapin
Data General Corporation MS E111
4400 Computer Drive
Westborough, MA 01580
,---------------------------------,
X3S33/X3T56/81-85 | WORKING PAPER |
X3T5/81-171 | This document has not been re- |
X3T51/81-44 | viewed or approved by the appro-|
X3S37/81-71R | priate Technical Committee and |
| does not at this time represent |
| a USA consensus. |
'---------------------------------'
Connectionless Data Transmission
A. Lyman Chapin
-
ABSTRACT
1 Introduction
-
Over the past three years, a number of national and interna- tional standards organizations have expended the time and efforts of a great many people to achieve a description of an architectural Reference Model for interconnecting computer systems considered to be "open" by virtue of their mutual use of standard communication protocols and formats. The current description, the Reference Model of Open Systems Interconnection (RM/OSI)[1], is generally accepted by the International Organi- zation for Standardization (ISO), the International Telephone and Telegraph Consultatitive Committee (CCITT), the European Computer Manufacturer's Association (ECMA), and many national standards bodies, including the American National Standards Institute (ANSI), and has progressed to the status of a Draft Proposed Standard (DP7498) within ISO. It describes the con- cepts and principles of a communications architecture organized hierarchically, by function, into seven discrete layers, and prescribes the services that each layer must provide to the layer immediately above it (the uppermost layer provides its services to user applications, which are considered to be outside of the Open Systems Interconnection environment). Building on the services available to it from the next-lower layer, each layer makes use of standard OSI protocols which enable it to cooperate with other instances of the same layer (its "peers") in other systems (see Figure 1). This technique of grouping related functions into distinct layers, each of which implements a set of well-defined services that are used by the layer above, partitions a very complex, abstract problem - "how can the components of a distributed application, operating in potentially dissimilar environments, cooperate with each other?" - into a number of more manageable problems that enjoy a logical relationship to each other and can individually be more readily understood.
-
-
FIGURE 1 - General Model of an OSI Layer
-
-
A Note on OSI Terminology
-------------------------
-
of another system is how the other entity behaves, not how it is implemented. In particular, OSI is not concerned with how the interfaces between adjacent layers are implemented in an open system; any interface mechanism is acceptable, as long as it supports access to the appropriate standard OSI services. A major goal of the OSI standardization effort is generality. Ideally, the Reference Model should serve as the common archi- tectural framework for many different types of distributed systems employing a wide range of telecommunication technologies, and certainly an important measure of the success of OSI will be its ability to apply the standard architecture across a broad spectrum of user applications. The way in which the Reference Model has developed over the past four years reflects an awareness of this goal (among others): the process began with the identification of the essential concepts of a layered architecture, including the general architectural elements of protocols, and proceeded carefully from these basic principles to a detailed description of each layer. The organi- zation of the current Reference Model document [1] exhibits the same top-down progression. At the highest level, three elements are identified as basic to the architecture[1]: a) the application processes which exist within the Open Systems Interconnection environment;-
b) the connections which join the application processes and
-
permit them to exchange information; and
c) systems.
-
The assumption that a connection is a fundamental prerequisite
for communication in the OSI environment permeates the Reference
Model, and is in fact one of the most useful and important
unifying concepts of the architecture. A growing number of
experts in the field, however, believe that this deeply-rooted
connection orientation seriously and unnecessarily limits the
power and scope of the Reference Model, since it excludes a
large class of applications and implementation technologies that
have an inherently connectionless nature. They argue that the
architectural objectives of the Reference Model do not depend on
the exclusive use of connections to characterize all OSI
interactions, and recommend that the two alternatives - connec-
tion oriented data transfer, and connectionless data transmis-
sion - be treated as complementary concepts, which can be
applied in parallel to the different applications for which each
is suited.
on Connectionless Data Transmission[3], and Recommended Changes
to Section 3 of [the Reference Model] to Include Connectionless
Data Transmission[2]; and the importance of the issue was
recognized by the full subcommittee in a resolution[25] calling
for comments on the two documents from all member organizations.
The question of how the connectionless data transmission concept
should be reflected in the OSI architecture - and in particular,
whether or not it should become an integral part of the Re-
ference Model - will be debated again this summer, when the
current Draft Proposed Standard Reference Model becomes a Draft
International Standard. The remainder of this article will
explore the issues that surround this question.
2 What Is Connectionless Data Transmission?
Connectionless data transmission (CDT), despite the unfamiliar
name, is by no means a new concept. In one form or another, it
has played an important role in the specification of services
and protocols for over a decade. The terms "message mode"[ ],
"datagram"[35], "transaction mode"[22,23,24], and
"connection-free"[37,47] have been used in the literature to
describe variations on the same basic theme: the transmission of
a data unit in a single self-contained operation without
establishing, maintaining, and terminating a connection.
Since connectionless data transmission and connection-oriented
data transfer are complementary concepts, they are best under-
stood in juxtaposition, particularly since CDT is most often
defined by its relationship to the more familiar concept of a
connection.
2.1 Connection-Oriented Data Transfer
- Successful - - Unsuccessful -
(N)- | | (N)- | |
connect | |(N)-connect connect | | (N)-
------->| |indication ------->| | connect
request | | request | |indication
| |-------> | |------->
|(N)-LAYER | |(N)-LAYER |
(N)- | |<------- (N)- | |<-------
connect | | disconnect | | (N)-
<-------| |(N)-connect <-------| |disconnect
confirm | | response indication | | request
| | | |
Data Transfer
-------------
(N)- | | (N)- | |
data | | (N)-data data | |
------->| |indication ------->| | (N)-
request | | request | | data
| |-------> | |indication
|(N)-LAYER | |(N)-LAYER |------->
| | (N)- | |
| | data | |
| | <-------| |
| | confirm | |
| | | |
Connection Release
------------------
- User Initiated - - Provider Initiated -
(N)-dis | | | |
connect | | (N)- | | (N)-
------->|(N)-LAYER |(N)-disconnect disconnect|(N)-LAYER |disconnect
request | |indication <-------| |------->
| |-------> indication| |indication
| | | |
[Note: Much of the material in this section is
derived from reference 3]
-
- Prior negotiation.
In a connection-oriented interaction, no connection is esta- blished - and no data are transferred - until all parties agree on the set of parameters and options that will govern the data transfer. An incoming connection establishment request can be rejected if it asserts parameter values or options that are unacceptable to the receiver, and the receiver may in many cases suggest alternative parameter values and options along with his rejection. The reason for negotiation during connection establishment is the assumption that each party must reserve or allocate the resources (such as buffers and channels) that will be required to carry out data transfer operations on the new connection. Negotiation provides an opportunity to scuttle the establishment of a connection when the resources that would be required to support it cannot be dedicated, or to propose alternatives that could be supported by the available resources.
- Three-party Agreement.
The fundamental nature of a connection involves establishing and dynamically maintaining a three-party agreement concerning the transfer of data. The three parties - the two (N+1)-entities that wish to communicate, and the (N)-service that provides them with a connection - must first agree on their mutual willingness to participate in the transfer (see above). This initial agreement establishes a connection. Thereafter, for as long as the connection persists, they must continue to agree on the acceptance of each data unit transferred over the connection. "With a connection, there is no possibility of data transfer through an unwilling service to an unwilling partner, because the mutual willingness must be established before the data transfer can take place, and data must be accepted by the destination partner; otherwise, no data [are] transferred on that connection."[3]
- Connection Identifiers.
supplied by the (N)-service (in OSI parlance, an "(N)-connection-endpoint-identifier"). This is a locally-significant "shorthand" reference that uniquely identi- fies an established connection during its lifetime. Similarly, the protocol units that carry data between systems typically include a mutually-understood logical identifier rather than the actual addresses of the correspondents. This technique elimina- tes the overhead that would otherwise be associated with the resolution and transmission of addresses on every data transfer. In some cases, however - particularly when non-homogeneous networks are interconnected, and very location-sensitive addres- sing schemes are used - it can make dynamic routing of data units extremely difficult, if not impossible.
- Data Unit Relationship.
Once a connection has been established, it may be used to transfer one data unit after another, until the connection is released by one of the three parties. These data units are logically related to each other simply by virtue of being transferred on the same connection. Since data units are transferred over a connection in sequence, they are related ordinally as well. These data unit relationships are an impor- tant characteristic of connections, since they create a context for the interpretation of arriving data units that is indepen- dent of the data themselves. Because a connection maintains the sequence of messages associated with it, out-of-sequence, missing, and duplicated messages can easily be detected and recovered, and flow control techniques can be invoked to ensure that the message transfer rate does not exceed that which the correspondents are capable of handling. These characteristics make connection-based data transfer attractive in applications that call for relatively long-lived, stream-oriented interactions in stable configurations, such as direct terminal use of a remote computer, file transfer, and long-term attachments of remote job entry stations. In such applications, the interaction between communicating entities is modelled very well by the connection concept: the entities initially discuss their requirements and agree to the terms of their interaction, reserving whatever resources they will need; transfer a series of related data units to accomplish their mutual objective; and explicitly end their interaction, releas- ing the previously reserved resources. 2.2 Connectionless Data Transmission entities is more naturally modelled by the connectionless data transmission concept, which involves the transmission of a single self-contained data unit from one entity to another without prior negotiation or agreement, and without the as- surance of delivery normally associated with connection-based transfers. The users of a connectionless (N)-service may, of course, use their (N+1)-protocol to make any prior or dynamic arrangements they wish concerning their interpretation of the data transmitted and received; the (N)-service itself, however, attaches no significance to individual data units, and does not attempt to relate them in any way. Two (N+1)-entities communi- cating by means of a connectionless (N)-service could, for example, apply whatever techniques they might consider appro- priate in the execution of their own protocol (timers, retransmission, positive or negative acknowledgements, sequence numbers, etc.) to achieve the level of error detection and/or recovery they desired. Users of a connectionless, as opposed to connection-oriented, (N)-service are not restricted or inhibited in the performance of their (N+1)-protocol; obviously, though, the assumption is that CDT will be used in situations that either do not require the characteristics of a connection, or actively benefit from the alternative characteristics of connec- tionless transmission. Figure 3 illustrates schematically the single operation whereby a connectionless service may be employed to transmit a single data unit. Figure 4 shows a widely-implemented variation, sometimes called "reliable datagram" service, in which the service provider undertakes to confirm the delivery or non-delivery of each data unit. It must be emphasized that this is not a true connectionless service, but is in some sense a hybrid, combining the delivery assurance of connection-oriented service with the single-operation interface event of connection- less service. Many of those involved in OSI standardization activities have agreed on a pair of definitions for connectionless data transmission, one for architectural and conceptual purposes, and one for service-definition purposes[4]. The architectural definition, which has been proposed for inclusion in the Re- ference Model, is: "Connectionless Data Transmission is the transmission (not transfer) of an (N)-service-data-unit from a source (N)-service-access-point to one or more destination (N)-service-access-points without establishing an (N)-connection for the transmission." | | (N)-data | | request | | --------->| | | (N)-LAYER | | |---------> | | (N)-data | | indication | |-
FIGURE 3 - Connectionless Data Transmission
(N)-data | | request | | --------->| | | | (N)-data | (N)-LAYER |---------> | | indication <---------| | (N)-data | | confirm | |-
FIGURE 4 - "Reliable Datagram" Service
service descriptions for individual layers of the Reference Model, is:
"A Connectionless (N)-Service is one that accomplishes the transmission of a single self-contained (N)-service-data-unit between (N+1)-entities upon the performance of a single (N)-service access."
Both of these definitions depend heavily on the distinction between the terms "transmit", "transfer", and "exchange": Transmit: "to cause to pass or be conveyed through space or a medium." This term refers to the act of conveying only, without implying anything about reception. Transfer: "to convey from one place, person, or thing, to another." A one-way peer-to-peer connotation restricts the use of this term to cases in which the receiving peer is party to and accepts the data transferred. Exchange: "to give and receive, or lose and take, reciprocally, as things of the same kind." A two-way peer-to-peer connotation restricts the use of this term to cases in which both give and receive directions are clearly evident. These definitions are clearly of limited usefulness by themselves. They do, however, provide a framework within which to explore the following characteristics of CDT:
- "One-shot" Operation.
The most user-visible characteristic of connectionless data transmission is the single service access required to initiate the transmission of a data unit. All of the information re- quired to deliver the data unit - destination address, quality of service selection, options, etc. - is presented to the connectionless (N)-service provider, along with the data, in a single logical service-access operation that is not considered by the (N)-service to be related in any way to other access operations, prior or subsequent (note, however, that since OSI is not concerned with implementation details, the specific interface mechanism employed by a particular implementation of connectionless service might involve more than one interface exchange to accomplish what is, from a logical standpoint, a single operation). Once the service provider has accepted a data unit for connectionless transmission, no further communica- tion occurs between the provider and the user of the service concerning the fate or disposition of the data.
- Two-party Agreement.
Connection-oriented data transfer requires the establishment of a three-party agreement between the participating (N+1)-entities and the (N)-service. A connectionless service, however, invol- ves only two-party agreements: there may be an agreement between the corresponding (N+1)-entities, unknown to the (N)-service, and there may be local agreements between each (N+1)-entity and its local (N)-service provider, but no (N)-protocol information is ever exchanged between (N)-entities concerning the mutual willingness of the (N+1)-entities to engage in a connectionless transmission or to accept a particular data unit. In practice, some sort of a priori agreement (usually a system engineering design decision) is assumed to exist between the (N+1)-entities and the (N)-service concerning those parameters, formats, and options that affect all three parties as a unit. However, considerable freedom of choice is preserved by allowing the user of a connectionless service to specify most parameter values and options - such as transfer rate, acceptable error rate, etc. - at the time the service is invoked. In a given implementation, if the local (N)-service provider determines immediately (from information available to it locally) that the requested operation cannot be performed under the conditions specified, it may abort the service primitive, returning an implementation-specific error message across the interface to the user. If the same determination is made later on, after the service-primitive interface event has completed, the transmis- sion is simply abandoned, since users of a connectionless service can be expected to recover lost data if it is important for them to do so.
- Self-contained Data Units.
Data units transmitted via a connectionless service, since they bear no relationship either to other data units or to a "higher abstraction" (such as a connection), are entirely self-contained. All of the addressing and other information needed by the service provider to deliver a data unit to its destination must be included in each transmission. On the one hand, this represents a greater overhead than is incurred during the data transfer phase of a connection-oriented interaction; on the other, it greatly simplifies routing, since each data unit carries a complete destination address and can be routed without reference to connection-related information that may not, for example, be readily available at intermediate nodes.
- Data Unit Independence.
connectionless service begins the transmission of a single data unit. Nothing about the service invocation, the transmission of the data by the connectionless service, or the data unit itself affects or is affected by any other past, present, or future operation, whether connection-oriented or connectionless. A series of data units handed one after the other to a connection- less service for delivery to the same destination will not necessarily be delivered to the destination in the same order; and the connectionless service will make no attempt to report or recover instances of non-delivery. Note: A number of popular variations on CDT include features that run counter to those described above. These variations deserve to be discussed on their own merits, but should not be confused with the architectural concept of connectionless data transmission. These characteristics make CDT attractive in applications that involve short-term request-response interactions, exhibit a high level of redundancy, must be flexibly reconfigurable, or derive no benefit from guaranteed in-sequence delivery of data. 3 The Rationale for Connectionless Data Transmission Because CDT is not as widely understood as connection-oriented data transfer, it has often been difficult in the course of developing service and protocol definitions to adduce a ration- ale for incorporating CDT, and even more difficult to determine appropriate locations for connectionless service within the layered hierarchy of OSI. This section addresses the first concern; the next section will deal with the second. The most natural way to discover the power and utility of the CDT concept is to examine applications and implementation technologies that depend on it. The following observations are distilled from the specifications and descriptions of actual protocols and systems (many of which have been implemented), and from the work of individuals and organizations engaged in the OSI standardization effort (quoted material is from reference 3, except where otherwise noted). They are divided into seven (occassionally overlapping) categories which classify the applications for which CDT is well suited. gathering data from dedicated measurement stations; a network status monitor constantly refreshing its knowledge of a network environment; and an automatic alarm or security system in which each component regularly self-tests and reports the result, are all engaged in this type of interaction, in which a "large number of sources may be reporting periodically and asynchron- ously to a single reporting point. In a realtime monitoring situation, these readings could normally be lost on occassion without causing distress, because the next update would be arriving shortly. Only if more than one successive update failed to arrive within a specified time limit would an alarm be warranted. If, say, a fast connect/disconnect three-way handshake cost twice as much as a one-way [connectionless] data transmission which had been system engineered to achieve a certain acceptable statistical reliability figure, the cost of connection-oriented inward data collection for a large distri- buted application could be substantially greater than for [connectionless collection], without a correspondingly greater benefit to the user."[3] Outward data dissemination is in a sense the inverse of the first category; it concerns the distribution of a single data unit to a large number of destinations. This situation is found, for example, when a node joins a network, or a commonly-accessible server changes its location, and a new address is sent to other nodes on the network; when a synchroni- zing message such as a real-time clock value must be sent to all participants in some distributed activity; and when an operator broadcasts a nonspecific message (e.g., "Network coming down in five minutes"). In such cases, the distribution cost (including time) may far exceed the cost of generating the data; control- ling the overall cost depends on keeping the cost of dissemina- tion as low as possible. Request-response applications are those in which a service is provided by a commonly accessible server process to a large number of distributed request sources. The typical interaction consists of a single request followed by a single response, and usually only the highest-level acknowledgement - the response itself - is either necessary or meaningful. Many commercial applications (point of sale terminals, credit checking, reserva- tion systems, inventory control, and automated banking systems) and some types of industrial process control, as well as more general information retrieval systems (such as videotex), fall into this category. In each case, the knowledge and expectation of each application component as to the nature of the interac- tion is represented in an application-process design and imple- mentation that is known in advance, outside of OSI; lower level negotiations, acknowledgements, and other connection-related functions are often unnecessary and cumbersome. An example of an application that combines the characteristics of inward data collection, outward data dissemination, and request-response interaction is described by the Working Group on Power System Control Centers of the IEEE Power Engineering Society in a recent letter to the chairman of ANSI committee X3T51 concerning the use of data communication in utility control centers[17]. They note that "a utility control center receives information from remote terminal units (located at substations and generating plants) and from other control centers, performs a variety of monitoring and control functions, and transmits commands to the remote terminals and coordinating information to other control centers." During the course of these operations, the following conditions occur: 1) Some measurements are transmitted or requested from remote terminals or control centers every few seconds. No attempt is necessarily made to recover data lost due to transmission error; the application programs include provisions for proper operation when input data is occassionally missing. [Inward data collection] 2) Some data items are transferred from commonly accessed remote sites or multi-utility pool coordination centers on a request-response basis. [Request-response interaction] 3) In some cases, an application program may require that some measurements be made simultaneously in a large number of locations. In these cases, the control center will broadcast a command to make th affected measurements. [Outward data dissemination]In closing, they note that "utility control centers around the world use data communications in ways similar to those in the United States."
Broadcast and multicast (group addressed) communication using connection-oriented services is awkward at best and impossible at worst, notwithstanding the occassional mention of "multi-endpoint connections" in the Reference Model. Some characteristics of connection-based data transfer, such as sequencing and error recovery, are very difficult to provide in a broadcast/multicast environment, and may not even be desirable; and it is not at all easy to formulate a useful definition of broadcast/multicast acknowledgement that can be supported by a low-level protocol. Where group addressing is an important application consideration, connectionless data trans- mission is usually the only choice. telemetry, and remote command and control, involving a high level of data redundancy and/or real-time transmission requirements, may profit from the fact that CDT makes no effort to detect or recover lost or corrupted data. If the time span during which an individual datum is meaningful is relatively short, since it is quickly superceded by the next - or if, as in digitized voice transmission, the loss or corruption of one or even several data units is insignificant - the application might suffer far more from the delay that would be introduced as a connection-oriented service dealt with a lost or out-of-sequence data unit (even if retransmission or other recovery procedures were not invoked) than it would from the unreported loss of a few data units in the course of a connectionless exchange. Other special considerations - such as the undesirability, for security reasons, of maintaining connection-state information between data transfers in a military command and control system - add force to the argument that CDT should be available as an alternative to connection-oriented data transfer. Local area networks (LANs) are probably the most fertile ground for connectionless services, which find useful application at several layers. LANs employ intrinsically reliable physical transmission media and techniques (baseband and broadband coaxial cable, fiber optics, etc.) in a restricted range (generally no greater than 1 or 2 kilometers), and are typically able to achieve extremely low bit error rates. In addition, the media-access contention mechanisms favored by LAN designers handle transmission errors as a matter of course. The usual approach to physical interconnection ties all nodes together on a common medium, creating an inherently broadcast environment in which every transmission can be received by every station. Taking advantage of these characteristics virtually demands a connectionless data link service, and in fact most current and proposed LANs - the Xerox Ethernet[43], the proposed IEEE 802 LAN standard[14,46], and many others - depend on such a service. As a bonus, because connectionless services are simpler to implement - requiring only two or three service primitives - inexpensive VLSI implementations are often possible. In addition, the applications for which LANs are often installed tend to be precisely those best handled by CDT. Consider this list of eight application classes identified by the IEEE 802 Interface Subcommittee as targets for the 802 LAN standard[46]: 1. Periodic status reporting - telemetry data from instrumentation, monitoring devices associated with static or dynamic physical environments;
2. Special event reporting - fire alarms, overload or stressing conditions;
3. Security control - security door opening and closing, system recovery or initialization, access control;
- File transfer;
5. Interactive transactions - reservation systems, electronic
messaging and conferencing;
6. Interactive information exchange - communicating text and
word processors, electronic mail, remote job entry;
7. Office information exchange - store and forward of digitized
voice messages, digitized graphic/image handling;
8. Real-time stimulus and response - universal product code
checkout readers, distributed point of sale cash registers,
military command and control, and other closed-loop and
real-time applications.
Of these, almost all have already been identified as classic
examples of applications that have an essentially connectionless
nature. Consider this more detailed example of (8): a local
area network with a large number of nodes and a large number of
services (e.g., file management, printing, plotting, job
execution, etc.) provided at various nodes. In such a
configuration, it is impractical to maintain a table at each
node giving the address of every service, since changing the
location of a single service would require updating the address
table at every node. An alternative is to maintain a single
independent "server lookup" service, which performs the function
of mapping the name of a given service to the address of a
server providing that service. The server-lookup server re-
ceives requests such as, "where is service X?", and returns the
address at which an instance of service X is currently located.
Communication with the server-lookup server is inherently
self-contained, consisting of a single request/response
exchange. Only the highest-level acknowledgement - the response
from the lookup service giving the requested address - is at all
significant. The native reliability of the local area network
ensures a low error rate; if a message should be lost, no harm
is done, since the request will simply be re-sent if a timely
response does not arrive. Such an interaction is poorly model-
led by the connection-oriented paradigm of opening a connection,
transferring a stream of data, and closing the connection. It
is perfectly suited to connectionless transmission techniques.
and a number of related activities, such as gateway-to-gateway
communication, exhibit the request-response, inward data
collection, and outward data dissemination characteristics that
are well supported by CDT. One of the best examples of a
connectionless internetwork service is described in a document
published by the National Bureau of Standards (Features of
Internetwork Protocol[29], which includes a straightforward
discussion of the merits of the connectionless approach:
"The greatest advantage of connectionless
service at the internet level is simplicity,
particularly in the gateways. Simplicity is
manifested in terms of smaller and less compli-
cated computer code and smaller computer storage
requirements. The gateways and hosts are not
required to maintain state information, nor
interpret call request and call clear commands.
Each data-unit can be treated
independently...Connectionless service assumes a
minim[al] service from the underlying
subnetworks. This is advantageous if the
networks are diverse. Existing internet proto-
cols which are intended for interconnection of a
diverse variety of networks are based on a
connectionless service [for example the PUP
Internetwork protocol[44], the Department of
Defence Standard Internet Protocol[31], and the
Delta-t protocol developed at Lawrence Livermore
Laboratory[45]]."
The principle motivating the development of internetwork servi-
ces and protocols that make few assumptions about the nature of
the individual network services (the "lowest common denominator"
approach) was formulated by Carl Sunshine as the "local net
independence principle"[39]: "Each local net shall retain its
individual address space, routing algorithms, packet formats,
protocols, traffic controls, fees, and other network character-
istics to the greatest extent possible." The simplicity and
robustness of connectionless internetworking systems guarantee
their widespread use as the number of different network types -
X.25 networks, LANs, packet radio networks, other broadcast
networks, and satellite networks - increases and the pressures
to interconnect them grow.
4 CDT and the OSI Reference Model
architecture. As a basis for deriving standard OSI services and
protocols, however, it has a greater impact on some layers of
the Reference Model than on others. Careful analysis of the
relative merits of connectionless and connection-oriented
operation at each layer is necessary to control the prolifera-
tion of incompatible or useless options and preserve a balance
between the power of the complementary concepts and the stabili-
zing objective of the OSI standardization effort.
Figure 5 illustrates the layered OSI hierarchy as it is most
commonly represented (it shows two instances of the hierarchy,
representing the relationship between two OSI systems). The
following sections discuss the CDT concept in the context of
each of the seven layers.
4.1 Physical Layer
The duality of connections and connectionless service is diffi-
cult to demonstrate satisfactorily at the physical layer,
largely because the concept of a physical "connection" is both
intuitive and colloquial. The physical layer is responsible for
generating and interpreting signals represented for the purpose
of transmission by some form of physical encoding (be it
electrical, optical, acoustic, etc.), and a physical connection,
in the most general sense (and restricting our consideration, as
does the Reference Model itself, to telecommunications media),
is a signal pathway through a medium or a combination of media.
Is a packet radio broadcast network, then, using a
"connectionless" physical service? No explicit signal pathway
through a medium or media is established before data are
transmitted. On the other hand, it can easily be argued that a
physical connection is established with the introduction of two
antennae into the "ether"; and if the antennae are aimed at each
other and designed to handle microwave transmission, the impres-
sion that a physical connection exists is strengthened. Whether
or not one recognizes the possibility of connectionless physical
services - other than purely whimsical ones - will probably
continue to depend on one's point of view, and will have no
effect on the development of actual telecommunication systems.
4.2 Data Link Layer
,---------------------, ,---------------------,
| | | |
Level 7 | Application Layer |<---------->| Application Layer |
| | | |
|----------|----------| |----------|----------|
| | | |
Level 6 | Presentation Layer |<---------->| Presentation Layer |
| | | |
|----------|----------| |----------|----------|
| | | |
Level 5 | Session Layer |<---------->| Session Layer |
| | | |
|----------|----------| |----------|----------|
| | | |
Level 4 | Transport Layer |<---------->| Transport Layer |
| | | |
|----------|----------| |----------|----------|
| | | |
Level 3 | Network Layer |<---------->| Network Layer |
| | | |
|----------|----------| |----------|----------|
| | | |
Level 2 | Data Link Layer |<---------->| Data Link Layer |
| | | |
|----------|----------| |----------|----------|
| | | |
Level 1 | Physical Layer |<---------->| Physical Layer |
| | | |
'---------------------' '---------------------'
concept of connectionless data transmission. The previous
discussion of local area networking has already made the point
that the high-speed, short-range, intrinsically reliable broad-
cast transmission media used to interconnect stations in local
area networks are complemented both functionally and concep-
tually by connectionless data link techniques.
One of the organizations currently developing a local area
network data link layer standard - the Data Link and Media
Access (DLMAC) subcommittee of IEEE 802 - has recognized both
the need to retain compatibility with existing long-haul techni-
ques and the unique advantages of CDT for local area networks by
proposing that two data link procedures be defined for the IEEE
802 standard.
In one procedure, information frames are unnumbered and may be
sent at any time by any station without first establishing a
connection. The intended receiver may accept the frame and
interpret it, but is under no obligation to do so, and may
instead discard the frame with no notice to the sender. Neither
is the sender notified if no station recognizes the address
coded into the frame, and there is no receiver. This
"connectionless" procedure, of course, assumes the "friendly"
environment and higher-layer acceptance of responsibility that
are usually characteristic of local area network
implementations.
The other procedure provides all of the sequencing, recovery,
and other guarantees normally associated with
connection-oriented link procedures. It is in fact very similar
to the ISO standard HDLC balanced asynchronous mode procedure.
Data link procedures designed for transmission media that
(unlike those used in local area networks) suffer unacceptable
error rates are almost universally connection-based, since it is
generally more efficient to recover the point-to-point
bit-stream errors detectable by connection-oriented data link
procedures at the data link layer (with its comparatively short
timeout intervals) than at a higher layer.
4.3 Network Layer
fact, internetwork services are provided by the Network Layer).
CDT also facilitates dynamic routing in packet- and
message-switched networks, since each data unit (packet or
message) can be directed along the most appropriate "next hop"
unencumbered by connection-mandated node configurations.
Examples of more or less connectionless network layer designs
and implementations abound: Zilog's Z-net (which offers both
"reliable" and "unreliable" service options); DECNET's
"transport layer" (which corresponds to the OSI Network layer);
Livermore Lab's Delta-t protocol (although it provides only a
reliable service, performing error checking, duplicate
detection, and acknowledgement); the User Datagram protocol[48];
and the Cyclades network protocol[38]. In fact, even the
staunchly connection-oriented X.25 public data networks
(Canada's Datapac is the best example) generally emply what
amounts to a connectionless network-layer service in their
internal packet switches, which enables them to perform flexible
dynamic routing on a packet-by-packet basis.
4.4 Transport Layer
The connectionless transport service is important primarily in
systems that distinguish the Transport layer and everything
below it as providing something generically named the "Transport
Service", and abandon or severely compromise adherence to the
OSI architecture above the Transport layer. In such systems a
connectionless transport service may be needed for the same
reasons that other (more OSI-respecting) systems need a connec-
tionless application service. Otherwise, the purpose of defin-
ing a connectionless transport service is to enable a uniformly
connectionless service to be passed efficiently through the
Transport layer to higher layers.
4.5 Session Layer
4.6 Presentation Layer
Very much the same considerations apply to the Presentation
layer as apply to the Session layer.
4.7 Application Layer
The most obvious reason to define a connectionless application
service - to give user application processes access to the
connectionless services of the architecture - is not the only
one. The application layer performs functions that help user
application processes to converse regarding the meaning of the
information they exchange, and is also responsible for dealing
with the overall system management aspects of the OSI operation.
Over and above the many user-application requirements for
connectionless service, it may be profitably employed by system
management functions that monitor and report on the status of
resources in the local open system; by application layer manage-
ment functions that need to interact in a request-response mode
with similar functions in other systems to perform security
access control; and by user application process functions that
monitor the status of activities in progress.
The potential availability of two complementary services at each
layer of the architecture raises an obvious question - how to
choose between them? It should be clear at this point that
unilateral exclusion of one or the other, although it may
simplify the situation for some applications, is not a general
solution to the problem. There are actually two parts to the
question: how to select an appropriate set of cooperative
services for all seven layers during the design of a particular
open system; and, if one or more layers of the system will offer
both connection-oriented and connectionless services, how to
provide for the dynamic selection of one or the other in a given
circumstance.
The second part is easiest to dispose of, since actual systems -
as opposed to the more abstract set of services and protocols
collected under the banner of OSI - will generally be con-
structed in such a way as to combine services cooperatively,
with some attention paid to the way in which they will interact
to meet specific goals. Although two services may be provided
at a given layer, logical combinations of services for different
applications will generally be assembled according to relatively
simple rules established during the design of the system.
support and the characteristics of the preferred implementation
technologies will also answer the first question. A system
designed primarily to transport large files over a long-haul
network would probably use only connection-oriented services.
One designed to collect data from widely scattered sensors for
processing at a central site might provide a connectionless
application service but use a connection-oriented network
service to achieve compatibility with a public data network.
Another system, built around a local area network bus or ring,
might use a connectionless data link service regardless of the
applications supported; if several LANs sere to be
interconnected, perhaps with other network types, it might also
employ a connectionless internetwork service.
^ ^ (N+1)-LAYER
| |
| |
----------------o------------------------------o----------------
| |
,-------------------------, ,-------------------------,
| Offers a connectionless | | Offers a connection- |
| (N)-service | | oriented (N)-service |
| | | | | |
| (N)-LAYER | OR | (N)-LAYER |
| | | | | |
| Uses a connection- | | Uses a connectionless |
| oriented (N-1)-service | | (N-1)-service |
'-------------------------' '-------------------------'
| |
----------------o------------------------------o----------------
| |
| |
v v (N-1)-LAYER
-
-
-
-
FIGURE 6 - Service Type Conversion
-
-
-
^ ^ (N+1)-LAYER
| |
| |
----------------o------------------------------o----------------
| |
,-------------------------, ,-------------------------,
| Offers a connectionless | | Offers a connection- |
| (N)-service | | oriented (N)-service |
| | | | | |
| (N)-LAYER | OR | (N)-LAYER |
| | | | | |
| Uses a connectionless | | Uses a connection- |
| (N-1)-service | | oriented (N-1)-service |
'-------------------------' '-------------------------'
| |
----------------o------------------------------o----------------
| |
| |
v v (N-1)-LAYER
5 Summary
Support for incorporating connectionless data transmission as a
basic architectural element of the Reference Model has grown as
understanding of the concept has become more widespread. The
protocol development sponsored by various agencies of the U.S.
Department of Defense, for example, have long recognized connec-
tions and connectionless transmission as complementary concepts,
and have employed both. Similar work being carried out by a
division of the Institute for Computer Science and Technology at
the National Bureau of Standards, the result of which will be a
series of Federal Information Processing Standards, depends
heavily on connectionless as well as connection-oriented
concepts. The importance of CDT to some of these U.S. efforts
is reflected in comments received by ANSI committee X3T5 during
the recent Reference Model ballot period, one of which states
that "Publication of this material [DP7498] without incorpora-
tion of the concerns associated with Connectionless Data
Trans[mission] makes a mockery of U.S. interests."[18] A some-
what less emotional expression of the same sentiment is embodied
in the official U.S. Position on Connectionless Data
Transmission[9], in which X3T5, the responsible U.S.
organization, "endorses SC16/N555 [Recommended Changes to
Section 3 of [the Reference Model] to Include CDT] without
exception and announces its intention to pursue vigorously the
incorporation of CDT as the first major extension to the Basic
Reference Model of OSI." In the same document, X3T5 notes that
it "intends to issue and maintain a version of DP7498 to be
referred to as DP7498-prime, incorporating the CDT extensions."
That there is also significant international support for the CDT
concept is clear, however, from the membership of the ISO
SC16/WG1 Ad Hoc Group on Connectionless Data Transmission, which
produced the N555 document last November; it includes represen-
tatives from France, Japan, Germany, and the United Kingdom as
well as from the U.S. Those who believe that the CDT concept is
an essential part of the OSI architecture hope that eventually
the DP7498-prime document, or its successor, will replace the
exclusively connection-oriented Reference Model before the
latter becomes an International Standard.
6 Acknowledgements
APPENDIX A - Vocabulary
-
OSI Terminology The following terms are defined in either the text or the vocabulary annex (or both) of the Draft Proposed Reference Model of OSI (ISO/DP7498). Some terms are given more than one defini- tion in different sections of the Reference Model; these are marked with an asterisk (*), to indicate that selection of the accompanying definition involved the author's personal judgement. [to be supplied] (N)-connection (N)-service-access-point (N)-service-access-point-address (N)-layer system (N)-entity (N)-connection-endpoint-identifier CDT Terminology The following terms, not yet part of the standard OSI vocabulary, relate to the concept of connectionless data transmission. "Connectionless Data Transmission is the transmission (not transfer) of an (N)-service-data-unit from a source (N)-service-access-point to one or more destination (N)-service-access-points without establishing an (N)-connection for the transmission." transmission of a single self-contained (N)-service-data-unit between (N+1)-entities upon the performance of a single (N)-service access." Transmit: "to cause to pass or be conveyed through space or a medium." This term refers to the act of conveying only, without implying anything about reception. Transfer: "to convey from one place, person, or thing, to another." A one-way peer-to-peer connotation restricts the use of this term to cases in which the receiving peer is party to and accepts the data transferred. Exchange: "to give and receive, or lose and take, reciprocally, as things of the same kind." A two-way peer-to-peer connotation restricts the use of this term to cases in which both give and receive directions are clearly evident.datagram
unit-data transfer/transmission
transaction (from SC1/N688)
data transmission (from DIS 2382 Section 9)1. Data Processing - Open Systems Interconnection - Basic Reference Model. Source: ISO/TC97/SC16 Reference: ISO/DP7498 X3T51/80-67 X3S33/X3T56/80-121 X3S37/80-115 Date: 12/80 2. Recommended Changes to Section 3 of 97/16 N537, Basic Specifications of the Reference Model of OSI, to Include Connectionless Data Transmission. Source: ISO/TC97/SC16/WG1 Ad Hoc Group on Connectionless Data Transmis- sion Reference: ISO/TC97/SC16/N555 X3S37/81-9 X3T51/80-68 X3S33/X3T56/80-122 Date: 11/80 3. Report of the Ad Hoc Group on Connectionless Data Transmission. Source: ISO/TC97/SC16/WG1 Ad Hoc Group on Connectionless Data Transmis- sion Reference: ISO/TC97/SC16/N566 X3T51/80-69 X3S33/X3T56/81-13 X3S37/81-35 Date: 11/804. Definitions of the Term "Connectionless Data Transmission"
(a letter to the chairman of ANSC X3T51 from the acting chairman of ANSC X3T56).- Connectionless Provisions for OSI Reference Model.
Source: ANSC X3S37 Reference: ISO/TC97/SC6/WG2/W12 X3S37/81-16R Date: 2/81 6. Comments on Recommended Changes to Section 3 of 97/16 N537, Basic Specification of the Reference Model of OSI, to include Connectionless Data Transmission, SC16/N555. Source: DIN (FRG) Reference: ISO/TC97/SC6/WG2/W10 Date: 2/81- Connectionless Data Transmission.
Source: X3S33/X3T56 Ad Hoc Group on Connec- tionless Data Transmission Reference: X3S33/X3T56/81-26 Date: 1/818. Contribution to Document ISO/TC97/SC16 N555 Concerning the
Extension of General Concepts from the Basic Reference Model to Connectionless Data Trans- fer Mode. Source: ISO/TC97/SC16/WG1 Ad Hoc Model Exten- sion Group B Reference: Date: 3/81- US Position on Connectionless Data Transmission.
10. Revision of SC16/N551 to Include Connectionless Data Transmission. Source: ANSC X3S33/X3T56 Reference: ISO/TC97/SC16/N602 X3S33/X3T56/81-67 X3T51/81-20 X3S37/81-17 Date: 3/81- Report of USA Vote and Comments on ISO DP7498.
Source: ANSC X3T5 Reference: ISO/TC97/SC16/N590 X3T51/81-29 Date: 3/81 12. USA Proposed Revision to Draft Basic Session Service Specification, ISO TC97/SC16 N553. Source: ANSC X3S33/X3T56 Reference: ISO/TC97/SC16/N597 X3S33/X3T56/81-39R X3T51/81-28 Date: 3/81 13. USA Proposed Revision to Draft Transport Service Specification, ISO TC97/SC16 N563.- Comments on Connectionless Data Transmission.
Source: Robert F. Stover, Honeywell Inc. Reference: Private communication Date: 4/81- Proposed Changes to the OSI Transport Layer.
Source: Gregory Ennis, Sytek Inc. Reference: X3T51 Reference Model Editing Group V3.B Date: 3/81 16. Review of the ISO Draft Proposal (DP 7498), Open System Interconnection Reference Model (Project IPSC-0168). Source: National Security Agency, Central Security Service, Department of Defense Reference: NSA/CSS Serial T095/008/81 X3T51 Reference Model Editing Group V3.F Date: 3/81- Comments on Draft Proposal ISO/DP7498.
Source: Working Group on Power System Control Centers, IEEE Power Engineer- ing Society Reference: X3T51 Reference Model Editing Group V3.I, V4.4 Date: 3/81 18. Review of ISO Draft Proposal 7498 (Open Systems Interconnection).- Proposed Improvements to Section 6 of DP7498.
Source: A. Lyman Chapin, Data General Corpora- tion Reference: X3T51 Reference Model Editing Group V3.M Date: 3/81- Comments on Section 7.4 of DP7498.
Source: ANSC X3S33/X3T56 Reference: X3S33/X3T56/81-30 X3T51 Reference Model Editing Group V3.H Date: 3/81- Comments on DP7498.
Source: ANSC X3S33/X3T56 Reference: X3S33/X3T56/81-60 X3T51 Reference Model Editing Group V3.N Date: 3/8122. USA Position Concerning Progression of the Reference Model
of Open Systems Interconnection (Parts I and II of USA Comments on N309). Source: ANSC X3T5 Reference: ISO/TC97/SC16/N405 X3T5/80-120 X3T51/80-43 Date: 9/80 23. Addenda to the USA Position Concerning Progression of OSI Reference Model (Parts I and II). 24. US Position on the WG1 Rapporteur's Report of October 1980. Source: ANSC X3T5 Reference: X3T5/80-142 X3T51/80-62 Date: 10/8025. Resolutions:
ISO/TC97/SC16 - Open Systems Interconnection: Berlin - November 12 - 14, 1980. Source: ISO/TC97/SC16 Reference: ISO/TC97/SC16/N570 X3S33/X3T56/80-11 Date: 11/80 26. NBS Analysis of Major US Government Requirements of Transport Protocol Services. Source: National Bureau of Standards, US Department of Commerce Reference: ISO/TC97/SC16/N404 X3T51/80-32 X3S33/X3T56/80-82 Date: 9/80- Features of the Transport and Session Protocols.
Source: National Bureau of Standards, US Department of Commerce Reference: X3S33/X3T56/80-30 Date: 3/80- Specification of the Transport Protocol.
- Features of Internetwork Protocol.
Source: National Bureau of Standards, US Department of Commerce Reference: X3T51/81-23 X3S33/X3T56/80-96 X3S37/81-31 Date: 7/80- Service Specification of an Internetwork Protocol.
Source: National Bureau of Standards, US Department of Commerce Reference: X3T51/81-24 X3S33/X3T56/81-18 X3S37/81-32 Date: 9/80- DoD Standard Internet Protocol.
Source: US Department of Defense Advanced Research Projects Agency Reference: X3S33/X3T56/80-17 X3S37/80-17 Date: 1/80 32. Connectionless Data Transfer (letter from the chairman of X3T51 to X3T55, X3T56, and X3S3). Source: John Day, Digital Technology, Inc. Reference: X3T51/80-76 Date: 12/80- Local Area Networks and the OSI Reference Model.
- An Introduction to Local Area Networks.
Source: David D. Clark, et. al. Reference: IEEE Proceedings 66:11 Date: 11/78- Issues in Packet-Network Interconnection.
Source: V.G. Cerf and P.T. Kirstein Reference: IEEE Proceedings 66:11 Date: 11/78- Connectionless Data Transfer.
Source: John Neumann, Microdata Corp. Reference: X3S33/X3T56/80-120 Date: 12/80- A Protocol for Packet Network Interconnection.
Source: V.G. Cerf and R.E. Kahn Reference: IEEE Transactions on Communication COM-22 No. 5 Date: 5/74- The CYCLADES End-to-End Protocol.
Source: H. Zimmermann Reference: Proceedings of the IEEE Vol. 66 No. 11 Date: 11/78 39. Interprocess Communication Protocols for Computer Networks. 40. CCITT Recommendation X.25 - Interface Between Data Ter- minal Equipment (DTE) and Data Circuit-Terminating Equipment (DCE) for Terminals Operating in the Packet Mode on Public Data Networks. Source: CCITT Study Group VII Reference: COM VII/489 Date: 11/80- An Analysis of ARPAnet Protocols.
-
-
Source:
Reference:
Date:
-
- ISO High-Level Data Link Control - Elements of Procedure.
Source: ISO Reference: ISO/IS4335 Date: 1977 43. ETHERNET Specification (Version 1.0) Source: Xerox Corporation Reference: X3T51/80-50 Date: 9/80- PUP: An Internetwork Architecture.
- Delta-t Protocol Preliminary Specification.
Source: R.W. Watson Reference: Lawrence Livermore Laboratories Date: 11/79- The Evolving IEEE 802 (Local Network) Standard.
Source: Bryan R. Hoover, Hewlett-Packard Corporation Reference: Date: 47. A System for Interprocess Communication in a Resource Sharing Computer Network. Source: D. Walden Reference: Communications of the ACM Vol. 15 Date: 4/72